Metrology for 5G and Emerging Wireless Technologies
Institution of Engineering and Technology (Verlag)
978-1-83953-278-8 (ISBN)
This edited book is the first to focus on metrology for current and future wireless communication technologies. It presents a comprehensive overview of the state-of-the-art measurement capabilities, testbeds and relevant R&D activities for 5G and emerging wireless technologies at a wide range of frequencies up to THz frequency bands. Several real-world field trials and use cases are also presented. The book focuses on R&D of measurement techniques and metrology for 5G and beyond that underpin all aspects, from signals, devices, antennas, systems and propagation environments to RF exposure. The presented materials describe advances in the triad of measurement system design, measurement techniques, and underpinning metrology required to cover many wireless communications aspects.
This book, Metrology for 5G and Emerging Wireless Technologies provides timely support to industry, academia, standard bodies and NMIs during the development of 5G and emerging wireless technologies and will support readers to enable further metrological R&D activities.
Tian Hong Loh is a principal research scientist at the National Physical Laboratory (NPL), UK. He leads work at NPL on a wide range of electromagnetic and wireless communication metrology research areas in support of the telecommunications industry. He has authored and co-authored over 160 publications and hold 6 patents. He is also a visiting professor at University of Surrey, and a visiting industrial fellow at University of Cambridge, UK. He is a UK representative of URSI Commission A (Electromagnetic Metrology), a topic editor of Electronics, an associate editor of IEEE Journal of Electromagnetics, RF and Microwaves in Medicine and Biology (J-ERM), IET Microwaves, Antennas & Propagation (MAP) Journal, IET Communications (COMMUN) Journal and International Union of Radio Science (URSI) radio science bulletin, a member of the IET and a senior member of the IEEE. He was the project coordinator of an European Association of National Metrology Institutes (EURAMET) European Metrology Programme for Innovation and Research (EMPIR) project on 'Metrology for 5G Communications', a guest editor of IET MAP special issue on 'Metrology for 5G Technologies', and was the TPC chair of the 2017 IEEE International Workshop on Electromagnetics (iWEM 2017). His research interests include metamaterials, computational electromagnetics, small antennas, smart antennas, multiple-input-multiple-output (MIMO), electromagnetic compatibility, wireless sensor networks, body-centric communication and 5G and beyond communications.
Chapter 1: Introduction to metrology for 5G and emerging wireless technologies
Part I: Waveform metrology
Chapter 2: Metrology for 5G link adaptation and signal-to-interference-plus-noise ratio
Part II: Device metrology
Chapter 3: Non-linear measurements for 5G devices and the associated uncertainties
Chapter 4: Multiphysics measurements of RF/microwave power amplifiers
Part III: Antenna metrology
Chapter 5: A metrological millimeter wave hybrid beamforming testbed with a large antenna array
Chapter 6: Assessment of broadband sources and defocusing effects of compact antenna test range for 5G antenna testing
Chapter 7: International intercomparison campaigns for mobile communication antenna characterizations towards 5G and beyond
Chapter 8: Numerical and experimental analyses of wearable antennas, including novel fabrication and metrology techniques
Chapter 9: 5G mm-wave mobile handset antenna system, measurements and evaluations
Part IV: System OTA metrology
Chapter 10: Over-the-air testing metrology of 5G radios
Chapter 11: Over-the-air testing with synthetic-aperture techniques
Chapter 12: Using reverberation chambers for mm-wave over-the-air and electromagnetic compatibility measurements
Chapter 13: Over-the-air testing for autonomous vehicle communications
Chapter 14: Performance evaluation and compliance testing of 5G/6G base stations, user-devices and systems
Part V: Propagation channel metrology
Chapter 15: Metrology for channel sounding
Chapter 16: Empirical mmWave channel measurements and modelling in indoor and outdoor complex environments for 5G communications
Chapter 17: Massive MIMO: real-world trials and practical solutions for 5G and beyond
Chapter 18: Millimetre-wave radio propagation measurements towards 5G NR standardizations
Chapter 19: Terahertz communications on various beyond 5G real-world use cases for IoT, railway, train, drone communications - propagation channel characterization and challenges
Part VI: RF exposure metrology
Chapter 20: Measurement of 5G new radio-base stations
Chapter 21: Metrology for RF-exposure from massive MIMO system
Chapter 22: Conclusions and future perspectives
| Erscheinungsdatum | 02.02.2022 |
|---|---|
| Reihe/Serie | Telecommunications |
| Verlagsort | Stevenage |
| Sprache | englisch |
| Maße | 156 x 234 mm |
| Themenwelt | Technik ► Nachrichtentechnik |
| ISBN-10 | 1-83953-278-5 / 1839532785 |
| ISBN-13 | 978-1-83953-278-8 / 9781839532788 |
| Zustand | Neuware |
| Haben Sie eine Frage zum Produkt? |
aus dem Bereich
