Marine Diesel Engines

Maintenance, Troubleshooting, and Repair

Nigel Calder (Autor)

Buch | Hardcover

224 Seiten

1991 | 2nd Revised edition
TAB Books Inc (Verlag)
978-0-07-009612-7 (ISBN)

Infos

Describes how marine diesel engines work, and discusses cleanliness, typical problems, routine maintenance, and selecting and installing an engine.

Autor

Niger Calder is the author of Marine Diesel Engines (1987, 1991) and Boatowner's Mechanical and Electrical Manual (1989, 1995), the success of which has made him the most sought-after marine how-to writer in the U.S. and U.K. He has published more than 800 magazine articles in SAIL, Cruising World, Ocean Navigator, Yachting World, etc., and lectures on cruising to sell-out crowds. He is also the author of The Cruising Guide to The Northwest Caribbean (IM, 1991) and Cuba: A Cruising Guide (Imray, 1996). He will be testing his newest ideas with his family during a six-month cruise to the Caribbean and South America this winter.

Inhalt

List of Troubleshooting Charts
Preface to the Second Edition
Introduction
One. Principles of Operation
Compression Ignition
Converting Heat to Power
Expansion and Cooling
Gasoline Engines
Cost and Power-to-Weight
Types of Diesels
The Crankshaft
Valves and Timing
Cylinders and Other Parts
Two. Details of Operation
Section One: The Air Supply
The Oxygen Supply
Volumetric Efficiency
Naturally Aspirated Engines
Superchargers and Turbochargers
Intercoolers and Aftercoolers
Section Two: Combustion
The Importance of Turbulence
Injector Spray Patterns
Techniques for Creating Turbulence
Section Three: Fuel Injection
Jerk Pumps
Distributor Pumps
Common Rail Systems
Injectors
Lift Pumps
Section Four: Governors
Simple Governors
Vacuum Governors
Section Five: Keeping Things Cool
Raw-Water Cooling
Heat Exchanger Cooling
Keel Cooling
Wet and Dry Exhausts
Two-Cycle Engines
Three. Cleanliness Is Next to Godliness
Clean Air
Clean Fuel
Clean Oil
Changing Filters
A Clean Engine
Four. Troubleshooting, Part One: Failure to Start
Section One: Failure to Crank
Water in the Engine
Starter Motor Circuits
Inertia and Pre-Engaged Starters
Battery Testing
Circuit Tests
Motor and Solenoid Diassembly, Inspection, and Repair
Flywheel Ring Gear
Section Two: Failure to Fire
An Unobstructed Airflow
Ignition Temperatures: Cold-Start Devices; Compression; Cranking Speed
Fuel Problems: Check the Obvious; Solenoid Valve; Fuel Filters; Bleeding (Purging) a Fuel System; Persistent Air in the Fuel Supply; Lift Pump (Feed Pump) Failure; Very Cold Weather; Serious Fuel Supply Problems; Starting Fluid and WD 40
Five. Troubleshooting, Part Two: Overheating, Smoke, Knocks, and Other Problems
Overheating
Smoke
Knocks
Misfiring Cylinders
Seizure
Poor Pick-up
Sticking or Bent Valve Stems
Engine Runaway
High Exhaust Back Pressure
High Crankcase Pressure
Water in the Crankcase
Low Oil Pressure
Rising Oil Level
High Oil Consumption
Inadequate Turbocharger Performance
Problems with Engine Instrumentation
Six. Maintenance and Repair Procedures, Part One
The Cooling System
Flexible Impeller Pumps
The Exhaust System
Governors
Fuel Injection Pumps
Injectors
Electrical Equipment
Gaskets
Winterizing
Seven. Maintenance and Repair Procedures, Part Two: Decarbonizing
Preparatory Steps
Cylinder Head Removal
Valves
Cylinders
Piston Removal
Piston Rings
Piston Pin Bearings
Connecting Rod Bearings
Replacing Pistons
Replacing Cylinder Heads
Replacing Push Rods and Rockers
Retiming an Engine
Valve Clearances, 4-Cycle Engines
Valve Clearances, 2-Cycle Engines
Accessory Equipment
Eight. Marine Transmissions
Planetary Transmissions
Two-Shaft Transmissions
Shaft Brakes
Maintenance
Clutch Adjustments on Manual Transmissions
Clutches on Hydraulic and Two-Shaft Transmissions
Overheating
Water in the Transmission
Loss of the Transmission Oil
Control Cables
Replacing an Output Shaft Seal
V-drives
Inboard/Outboards
Nine. Engine Selection and Installation
Section One: Engine Selection
Matching an Engine to Its Load
How Much Horsepower Do You Need?
BHP, SHP, and Auxiliary Equipment
Power-to-Weight Ratio
Section Two: The Power Train
Slip
Cavitation
Propeller Selection
Section Three: Mounting the Propeller Shaft
Struts and Cutless Bearings
Keeping the Water Out
Packing Adjustment and Replacement
Graphite Packing Tape
Rotary Seals
Section Four: Engine Beds and Alignment
Engine Beds
Couplings
Engine Alignment
Constant Velocity Joints (CVJs)
Vibration Analysis
Section Five: Auxiliary Systems
Ventilation
Fuel Tanks and Filters
Cooling
Exhaust
Auxiliary Equipment
Some Electrical Considerations
Safety Shut-downs
Serviceability
Appendix A. Tools
Appendix B. Spare Parts
Appendix C. Useful Tables
Appendix D. Freeing Frozen Fasteners
Glossary
Index

Produkt-Details

• Erscheint lt. Verlag: 22.12.1991
• Zusatzinfo: 246 Illustrations, unspecified
• Verlagsort: New York
• Sprache: englisch
• Maße: 191 x 244 mm
• Gewicht: 502 g
• Themenwelt: Technik ► Maschinenbau
• ISBN-10: 0-07-009612-0 / 0070096120
• ISBN-13: 978-0-07-009612-7 / 9780070096127
• Zustand: Neuware